BRITISH COLUMBIA CLASS 1 LICENCE TEST 4

0 votes, 0 avg

1 / 30

When coupling a truck-tractor to a semi-trailer:

The jaws of the fifth wheel should be in the locked position before coupling

The fifth wheel should be higher than the semi-trailer before making the connection

Corrections should be made if you notice slack during the tug test

It is essential that you have chocks at the front and rear of the semi-trailer wheel

2 / 30

When is it safe to remove the safety marks from a vehicle that is carrying dangerous goods?

At least one week after the last dangerous goods were unloaded from the vehicle

When the vehicle has been cleaned and purged of all residues of dangerous goods

After completing your final delivery of dangerous goods and doing a quick visual inspection for leaks

Before making the last delivery of dangerous goods

3 / 30

When inspecting the airlines on a vehicle with air brakes during a pre-trip inspection, you should:

Measure the pressure

Calibrate the air lines

Check the temperature

Ensure there are no cuts, abrasions or cracks in the air lines

4 / 30

According to this Provinces Hours of service legislation, under which of the following conditions would a driver not be allowed to drive?

If road conditions are dangerous

If he/she has already driven 10 hours during that shift

If he/she has had more than 3 work shifts that week

If he/she has already been on-duty for 15 hours

5 / 30

Which of the following belts should you check during a pre-trip inspection:

All belts on the front of the engine

Power steering belt

Alternator belt

Water pump belt

6 / 30

What is a possible disciplinary action assessed to a carrier due to failing to follow a written safety program?

Immediate loss of licence to operate that type of vehicle

Mandatory completion of a special safety course

Designation as a high-risk carrier

Charges laid in court

7 / 30

Which of the following statements about the holder of a Class 2 operator's licence is false?

He/she may operate any motor vehicle or combination of vehicles that the holder of a Class 3, 4 or 5 operator's licence may operate

He/she must provide a bus with a seating capacity of at least 20 passengers for the road test

He/she may only operate Class 1 and 6 vehicles for learning

An air brake 'Q' endorsement is required to operate air brake equipped vehicles

8 / 30

What is the purpose of a trip inspection?

Ensure the driver has the training and knowledge needed to safely operate the vehicle on the highway

Ensure the early identification of a vehicle problem and defects before the vehicle is operated on the highway

Ensure compliance with the provincial and federal legislation

Ensure the driver is aware of the major and minor defects he may have to deal while operating the vehicle on the highway

9 / 30

What are the four factors affecting the distance a commercial vehicle needs to stop?

Speed; weather; perception time; tire pressure

Brake condition; traction; weight; speed

Traction; speed; perception time; reaction time

Speed; brake condition; reaction time; weight

10 / 30

Qualifying for an air brake endorsement is mandatory to obtain what type of licence?

Class 2

Class 3

Class 4

Class 1

11 / 30

Which of the vehicles below would be required to stop at all uncontrolled railway crossings?

An ambulance

A semi-trailer carrying corrosive materials

A truck that has just finished unloading a delivery of flammable liquids

A 16-passenger tour bus

12 / 30

Ultimately, whose responsibility is it to ensure that employees have the proper training to work safely with dangerous goods?

The training provider

A dangerous goods inspector

The employee

The carrier

13 / 30

When conversing with or offering help to someone with disabilities, it is important to:

Identify yourself and provide reassurance about the transportation help you can provide

Respect their desire for personal space

All answers are correct

Consider their visual, hearing or physical impairment when speaking to them

14 / 30

As a school bus driver, you should never:

Drive with open front doors

Break the four-second following rule

Refuel a bus with passengers aboard

All answers are correct

15 / 30

What is lag time?

The sum of the perception time and the driver reaction time

The amount of time it takes for the air brake system to respond after the driver has applied pressure on the brake pedal

The amount of time it takes for the driver to notice the need to stop if he or she is not paying attention

The amount of time it takes between deciding to stop and actually applying pressure to the brake pedal

16 / 30

A “Q” endorsement is placed on ____________ driver’s licence when a driver successfully completes an approved by Province air brake course through an authorized organization.

Class 2

Class 1

Any class of

Class 3

17 / 30

Which of the vehicles below would be required to stop at all uncontrolled railway crossings?

a. A 16-passenger tour bus
b. A truck that has just finished unloading a delivery of flammable liquids
c. A semi-trailer carrying corrosive materials
d. An ambulance

Why are railway crossings potentially more dangerous for larger, heavier commercial vehicles?

a. These vehicles need more time to clear a crossing
b. These vehicles need to stop farther away from a crossing before proceeding safely
c. These vehicles need more speed to clear the crossing
d. These vehicles have to overcome the centrifugal force acting upon them

Corrosive materials can corrode:

a. Internal tissue
b. All answers are correct
c. Human skin
d. Metal

If a 'reserved lane' sign includes a list of hours of the day or days of the week on it, what do these mean?

a. They indicate when the vehicles represented on the sign are not permitted to drive in that
b. They indicate when any vehicle can drive in that lane
c. They indicate when that lane is reserved
d. They indicate when that lane is not reserved

When reversing a semi-trailer, you should:

a. Honk the horn only if there are other vehicles or bystanders in the vicinity
b. Turn the steering wheel in the opposite direction to where you want the trailer to go
c. Tap the throttle gently to begin reversing
d. Turn the steering wheel in the same direction to where you want to go

If safety marks are needed to indicate the presence of dangerous goods, where on the vehicle should they be placed?

On the side that will be most visible to other vehicles

On each side and each end of the trailer or transport unit

On the front of the lead trailer

At the end of the trailer or transport unit

18 / 30

When going through urban areas, all drivers must:

Activate the emergency hazard lights during night-time hours

Stop before every uncontrolled railway crossing

Drive only on the routes specified for trucks and dangerous goods vehicles

Encourage other vehicles to pass you before making left turns

19 / 30

If doing a pre-trip air brake inspection, which of the below would be acceptable pressure levels for the air supply valve and park control valve to pop out at?

35 PSI for the air supply valve and 15 PSI for the park control valve

50 PSI for the air supply valve and 30 PSI for the park control valve

70 PSI for the air supply valve and 50 PSI for the park control valve

Any pressure, as long as it is roughly equal for both valves

20 / 30

The law requires that the wheels of a parked vehicle be no farther than what distance from the curb?

25 centimetres

100 centimetres

50 centimetres

75 centimetres

21 / 30

If you are a school bus driver and there is a breakdown, the best course of action is to:

Place an approved warning device a few metres in front of the bus to alert other drivers

Activate the alternating flashing amber lights

Get all of the passengers off the bus as soon as possible regardless of the problem

Stop the bus as far off the roadway as practical and radio for help if you cannot fix the problem

22 / 30

Who is legally allowed to refuel a propane vehicle?

Only those over 18 years of age

Only those wearing protective gloves and clothing

Only those holding a Class 1 licence

Only those with proper certification or training

23 / 30

When driving a vehicle that is transporting dangerous goods, all pertinent documents should be located where?

Within reach or in a pocket mounted on the driver's door

In a labelled folder in the glove compartment of the passenger seat

As electronic copies on the driver's smartphone

Attached to the container holding the dangerous goods

24 / 30

When should you use a guide to assist with reversing?

If possible, always use a guide

When reversing to the right

When straight line reversing

When reversing to the left

25 / 30

Under this Provinces Vehicle Inspection Program:

Truck-tractors with a registered gross vehicle weight of more than 4,500kg must be inspected every 12 months

All answers are correct

Municipal transit buses are exempt from inspection only if they carry fewer than 11 passengers

Buses must be inspected more frequently than trucks

26 / 30

What are the warning signs of driver fatigue?

Accidentally drifting into other lanes

Daydreaming and disconnected thoughts

The feeling that vehicles in the rear view mirror appeared out of nowhere

All answers are correct

27 / 30

Which of the following statements about braking force is true?

If the weight of the vehicle is doubled, the braking force must be quadrupled

If the weight and the speed of the vehicle are doubled, the braking force must be increased by six times

If the speed of the vehicle is doubled, the braking force must be double

If the speed of a vehicle is doubled, the braking force must be quadrupled

28 / 30

When approaching a very busy intersection in an emergency vehicle with your sirens and lights activated, you should:

Watch out for pedestrians

All answers are correct correct

Ensure that other drivers have seen you before proceeding through a red light

When approaching a very busy intersection in an emergency vehicle with your sirens and lights activated, you should

29 / 30

When reversing to unload a dump vehicle, you should:

Position the guide so that he or she can see your path, but cannot be seen by you

Avoid using your mirrors and rely entirely on the hand signals of the guide

Back the vehicle to the passenger's side (right)

Use the backing alarm if the vehicle is equipped with one

30 / 30

What is the maximum permissible length for a straight truck?

10.5 metres

12.5 metres

11.0 metres

12.0 metres

Your score is

BRITISH COLUMBIA CLASS 1 LICENCE TEST 2023

What is a Class 1 Licence in British Columbia?

A Class 1 Licence in British Columbia allows you to operate a motor vehicle with a gross vehicle weight rating (GVWR) over 11,794 kg or any combination of vehicles where the towed vehicle has a GVWR of more than 4,600 kg.

Who is eligible to apply for a Class 1 Licence in British Columbia?

To be eligible for a Class 1 Licence, you must be at least 19 years old and have a Class 5 (full-privilege) driver’s licence in British Columbia.

What are the steps to obtain a Class 1 Licence in British Columbia?

The steps generally include passing a knowledge test, obtaining a learner’s Class 1 licence, completing a training program (if applicable), and passing a road test. The road test typically consists of a pre-trip inspection, an air brake test (if applicable), and a practical driving examination.

What topics are covered in the Class 1 Licence knowledge test?

The knowledge test includes questions related to air brakes (if applicable), safe driving practices, traffic laws and regulations, and general knowledge about operating Class 1 vehicles.

How can I prepare for the Class 1 Licence knowledge test in British Columbia?

You can prepare for the knowledge test by studying the British Columbia Commercial Driving Manual, which is available online. You can also take practice tests to assess your knowledge and identify areas where you might need additional study.

Do I need to take an air brake endorsement test for a Class 1 Licence?

If you plan to operate vehicles equipped with air brakes, you will need to obtain an air brake endorsement. This may require passing an air brake knowledge test in addition to the Class 1 Licence knowledge test.

What are the fees associated with getting a Class 1 Licence in British Columbia?

The fees for a Class 1 Licence can vary, and they may include the knowledge test fee, learner’s licence fee, and road test fee. There may also be additional costs for any required training programs.

Are there age restrictions for obtaining a Class 1 Licence in British Columbia?

Yes, you must be at least 19 years old to apply for a Class 1 Licence in British Columbia.

Is there a waiting period between passing the knowledge test and taking the road test for a Class 1 Licence?

The waiting period can vary, but generally, you will need to hold a Class 1 Learner’s Licence for a certain period and gain practical experience before taking the road test. This waiting period may be several months.

How long is a Class 1 Licence valid in British Columbia?

In British Columbia, a Class 1 Licence is typically valid for five years. You will need to renew it before the expiry date to continue driving commercially.

What is the difference between a Class 1 Licence and other commercial driver’s licences, like Class 2 or Class 3?

Class 1 allows you to drive the heaviest and most complex vehicles, typically tractor-trailers or semi-trucks. Class 2 and 3 licences are for buses and trucks of lighter classifications, respectively.

Please note that regulations and requirements may change over time, so it’s important to check with the British Columbia Ministry of Transportation and Infrastructure or visit their official website for the most up-to-date information regarding Class 1 Licence requirements and testing procedures.

When coupling a truck-tractor to a semi-trailer:

When is it safe to remove the safety marks from a vehicle that is carrying dangerous goods?

When inspecting the airlines on a vehicle with air brakes during a pre-trip inspection, you should:

According to this Provinces Hours of service legislation, under which of the following conditions would a driver not be allowed to drive?

Which of the following belts should you check during a pre-trip inspection:

What is a possible disciplinary action assessed to a carrier due to failing to follow a written safety program?

Which of the following statements about the holder of a Class 2 operator's licence is false?

What is the purpose of a trip inspection?

What are the four factors affecting the distance a commercial vehicle needs to stop?

Qualifying for an air brake endorsement is mandatory to obtain what type of licence?

Which of the vehicles below would be required to stop at all uncontrolled railway crossings?

Ultimately, whose responsibility is it to ensure that employees have the proper training to work safely with dangerous goods?

When conversing with or offering help to someone with disabilities, it is important to:

As a school bus driver, you should never:

What is lag time?

A “Q” endorsement is placed on ____________ driver’s licence when a driver successfully completes an approved by Province air brake course through an authorized organization.

If safety marks are needed to indicate the presence of dangerous goods, where on the vehicle should they be placed?

When going through urban areas, all drivers must:

If doing a pre-trip air brake inspection, which of the below would be acceptable pressure levels for the air supply valve and park control valve to pop out at?

The law requires that the wheels of a parked vehicle be no farther than what distance from the curb?

If you are a school bus driver and there is a breakdown, the best course of action is to:

Who is legally allowed to refuel a propane vehicle?

When driving a vehicle that is transporting dangerous goods, all pertinent documents should be located where?

When should you use a guide to assist with reversing?

Under this Provinces Vehicle Inspection Program:

What are the warning signs of driver fatigue?

Which of the following statements about braking force is true?

When approaching a very busy intersection in an emergency vehicle with your sirens and lights activated, you should:

When reversing to unload a dump vehicle, you should:

What is the maximum permissible length for a straight truck?

BRITISH COLUMBIA CLASS 1 LICENCE TEST 2023

For More Practice Watch our Videos

BC driver handbook

Leave a Comment Cancel Reply

When coupling a truck-tractor to a semi-trailer:

When is it safe to remove the safety marks from a vehicle that is carrying dangerous goods?

When inspecting the airlines on a vehicle with air brakes during a pre-trip inspection, you should:

According to this Provinces Hours of service legislation, under which of the following conditions would a driver not be allowed to drive?

Which of the following belts should you check during a pre-trip inspection:

What is a possible disciplinary action assessed to a carrier due to failing to follow a written safety program?

Which of the following statements about the holder of a Class 2 operator's licence is false?

What is the purpose of a trip inspection?

What are the four factors affecting the distance a commercial vehicle needs to stop?

Qualifying for an air brake endorsement is mandatory to obtain what type of licence?

Which of the vehicles below would be required to stop at all uncontrolled railway crossings?

Ultimately, whose responsibility is it to ensure that employees have the proper training to work safely with dangerous goods?

When conversing with or offering help to someone with disabilities, it is important to:

As a school bus driver, you should never:

What is lag time?

A “Q” endorsement is placed on ____________ driver’s licence when a driver successfully completes an approved by Province air brake course through an authorized organization.

If safety marks are needed to indicate the presence of dangerous goods, where on the vehicle should they be placed?

When going through urban areas, all drivers must:

If doing a pre-trip air brake inspection, which of the below would be acceptable pressure levels for the air supply valve and park control valve to pop out at?

The law requires that the wheels of a parked vehicle be no farther than what distance from the curb?

If you are a school bus driver and there is a breakdown, the best course of action is to:

Who is legally allowed to refuel a propane vehicle?

When driving a vehicle that is transporting dangerous goods, all pertinent documents should be located where?

When should you use a guide to assist with reversing?

Under this Provinces Vehicle Inspection Program:

What are the warning signs of driver fatigue?

Which of the following statements about braking force is true?

When approaching a very busy intersection in an emergency vehicle with your sirens and lights activated, you should:

When reversing to unload a dump vehicle, you should:

What is the maximum permissible length for a straight truck?

BRITISH COLUMBIA CLASS 1 LICENCE TEST 2023

For More Practice Watch our Videos

BC driver handbook

Related Posts

Leave a Comment Cancel Reply